If you are having problems connecting or pairing other Bluetooth devices with your Samsung Galaxy S6 phone, continue reading because we have listed a few workarounds and tips on resolving Bluetooth pairing problems on the Samsung Galaxy S6.
While many find pairing their Bluetooth devices straightforward, some users may experience difficulty pairing their devices first. If you are having trouble pairing your Galaxy S6 device, take a look at these helpful tips.
If you're having trouble connecting your Samsung Galaxy S6 phone or tablet to other Bluetooth-enabled devices or cannot get it to work at all, this article can help.
This post will find solutions to the most common issues related to using a Samsung phone or tablet and its built-in Bluetooth. We cover everything from basic troubleshooting tips to potential hardware issues and software fixes—so read on and get connected again in no time!
Basic Troubleshooting (Samsung Galaxy S6 Bluetooth Pairing Problems)
1. Ensure your Bluetooth is on
- We may have mistakenly disabled Bluetooth and have forgotten to re-enable it. If the Bluetooth icon is blue, that means it's ON
2. Ensure you have sufficient power
- Consider charging both devices above 15% before creating a connection.
3. Ensure that the device does not require a pairing app
- Some devices like Samsung earbuds and smartwatches need to be connected through the Galaxy Wearable app.
- Check out the device's support page to learn more about its Bluetooth pairing.
4. Ensure Bluetooth devices are within 30 feet
- Devices need to be close enough to each other before connecting. Consider moving the devices closer.
5. Test With Other Devices
- To help narrow down the problem, consider pairing it with other devices in your household or nearby. If other devices connect, the problem might be the Bluetooth device itself.
With the obvious out of the way, we can now concentrate on troubleshooting steps to help you fix problems even after establishing a Bluetooth connection by switching on Bluetooth on both devices.
How to Fix Samsung Galaxy S6 Bluetooth Pairing Problems
Method 1: Toggle your Bluetooth Connection
If the Bluetooth connection cannot be established or you fail to pair two devices, the first and most basic troubleshooting step is to toggle the Bluetooth connection. Pull down your phone's notification shade and look for the Bluetooth icon.
Switch Off the Bluetooth connection, wait 10 seconds and switch it on again. Now try to check if the phone can pair with the Bluetooth device or not.
Method 2: Remove All Paired Devices on your Samsung Galaxy S6 Device
Allow your Samsung Galaxy S6 phone to get a fresh start. You can do that by removing all the devices that were paired before.
Remove devices from your list and allow your phone to pair with the device again. To remove all paired devices, follow these steps:
- Head to Settings
- Tap Connections > Toggle Bluetooth On
- Tap on Bluetooth.
- You will see a list of devices that you have paired with
- There is a settings icon next to the name of each device. Tap on the icon to unpair the device.
- Do this for all the devices until you have no devices on your list.
Once all the devices are removed, your phone will begin scanning again for devices to connect. It should show the device you want to connect to. Try pairing it now and check if it works.
Method 3: Clear the Bluetooth cache and data on your Samsung Device and then try again
Suppose the Bluetooth on your Samsung Galaxy S6 phone has worked properly before, but you have recently started noticing Bluetooth pairing problems. In that case, you must consider clearing the cache files of your phone's Bluetooth. Cache files can get corrupted over time or due to specific system tweaks.
Removing these files is harmless. These files will be created once you start using Bluetooth again. To delete the Bluetooth cache, follow these steps:
- Navigate to Settings
- Tap on Apps
- You will find a whole list of applications on the next screen. Tap on the Sort icon (Then Tap Show System Apps)
- Look for Bluetooth and tap on it.
- On the next screen, tap Storage.
- Next, tap on Clear Cache and confirm your selection by tapping OK.
Once the cache is cleared, restart your phone and try connecting again. Check if your phone can establish the connection and if the connection works appropriately or not.
While clearing the cache removes cache files only, clearing the Bluetooth data is somewhat like resetting your Bluetooth connection so that it starts anew.
If you have any Bluetooth connections or pairings on Bluetooth's list of paired devices, all of those connections will be lost entirely.
You will have to pair the devices again after the data is cleared. We will clear the data so that any corrupted files are removed. Bluetooth will get a chance to start fresh. Follow these steps to clear your Bluetooth data:
- Navigate to Settings
- Tap on Apps
- You will find a whole list of applications on the next screen. Tap on the Sort icon (Then Tap Show System Apps)
- Look for Bluetooth and tap on it.
- On the next screen, tap Storage.
- Next, tap on Clear Data and confirm your selection by tapping OK.
Once the data has been wiped, restart your Galaxy S6 phone and switch on the Bluetooth connection. Let your phone or tablet search for the device and establish a connection with the other device in pairing mode.
Once the pairing is complete, check if the connection is working smoothly.
Method 4: Reset the network settings on your Galaxy S6
This will restore all the network settings to factory defaults (including the ones related to Wi-Fi and mobile data). Here's how to reset network settings:
- Navigate to Settings > General management
- Now, tap Reset > Reset network settings.
- Tap Reset settings.
- Enter a Pin or pattern
- Tap Reset settings to confirm the action.
Method 5: Toggle Airplane mode
Switch Off toggle mode, wait for 10 seconds, then switch it on again.
Method 6: Eliminate Problems Related to the Device You Are Connecting To
Before we begin troubleshooting the phone or the tablet, it is essential to rule out that the device is not the cause of the problem. To check if the device is working or not, connect it to another device like a different phone or a laptop and check if it works properly on the other devices.
If the Bluetooth device works fine on other phones or tablets, the problem lies with your phone and further troubleshooting should be done. But suppose the device does not connect to a different phone or another device either.
If that's the case, the problem lies with the device and you may have to follow the device manual for troubleshooting that particular device, or you must take it to the manufacturer to get it checked or replaced.
This is critical to ensure that the troubleshooting steps below are worthwhile for fixing your Samsung Galaxy S6 Bluetooth pairing problem.
Method 7: Restart your Galaxy S6 Phone and the device
Start by restarting your Samsung Galaxy S6 phone. A restart fixes simple errors and helps your phone start afresh. Switch on Bluetooth by pulling down your phone's notification shade and tapping on the Bluetooth icon after your phone restarts.
Make sure that the device is in pairing mode. Keep it close and give your phone time to scan all nearby devices.
Once your phone shows the device's name on the screen, tap on it and connect. If the connection is successful and the pairing works, the problem is gone; if the problem persists, try restarting the device you are trying to connect to.
Restart the device, put it in pairing mode, and check if the connection is established.
Method 8: Update your software
Your Galaxy S6 may be due for an update that can include releases for specific applications that may be causing a problem with the Bluetooth. Many things can be fixed with the help of an update.
Update your phone's software to ensure that your Bluetooth works as expected. To manually check for updates, follow these steps:
- Head to Settings > Software Update
- Tap Download and Install
- Then Tap Install Now
Once the update is complete, your phone will restart. After your phone restarts, try to use Bluetooth and check if the problem is gone.
Also, check for updates for the Bluetooth device you are trying to connect to your phone or tablet. There is a possibility that the device may be outdated and may be causing problems because of this. Try establishing the connection and check if it works as expected.
Method 9: Safe Mode
When you use your phone in Safe Mode, it disables all third-party apps and works in the most basic way. This will help you identify problems that may be related to third-party applications.
Bluetooth may be affected by a third-party application, and the best way to identify the problem is to use the phone in Safe Mode and check if the Bluetooth works in Safe Mode.
- Press and hold the Power button on your device till you see the Power menu > Tap Power Off.
- Press and hold the Power and Volume Down buttons simultaneously to turn the device on.
- Once the Samsung logo appears on the screen, you can let go of the power button. Ensure you keep holding the Volume Down Button
- Safe Mode will now appear at the bottom left of the screen.
How to Exit Safe Mode on a Samsung Galaxy S6 (3 Ways) :
- Press and hold the Power button for at least 6 seconds, then tap Restart.
- Press and hold the Power + Volume Down buttons for at least 5 seconds
- Swipe down from the top of the screen to access the Notification Panel, then tap on "Safe mode is on" To disable and restart.
Once the phone or tablet restarts, you will see Safe mode on the screen.
Try using Bluetooth in Safe Mode and check if it works. If you successfully do so, an application on your device may be interfering with the Bluetooth connection.
You can restart your Galaxy S6 phone to find the application. Then you can begin uninstalling the apps that you think may be causing the problem.
Method 10: Factory Reset your Samsung Galaxy S6
Resetting your Samsung Galaxy S6 phone to factory settings is a way to start with a clean slate. This will remove all data and third-party applications from your phone. Once you reset your device to factory settings, you must perform a backup.
Samsung devices already have the option to back up data. Still, transferring all-important photos, videos, and files to a computer is always preferable before you choose to reset your phone.
- Go to the Settings > General Management
- Tap Reset > Factory data reset.
Your phone will begin resetting your device by deleting all the information and data stored on your device. Once the reset process is complete, you can try using Bluetooth to check if it works. If your problem is gone, you can restore all the data to your device.
However, if your Bluetooth problem persists, there may be a problem with the physical connection, which could be causing the issue.
Take your phone to a professional or the manufacturer to solve the problem. For phones that are under warranty, you may be able to get a replacement.
Join our newsletter
Subscribe to our newsletter and never miss out on what's happening in the tech world. It's that simple.